Bu çalışmada, -196 oC'de 48 saat kriyojenik işlem görmüş ve görmemiş AZ91 ve AM60
magnezyum alaşımlarının korozyon ve aşınma özellikleri incelenmiştir. Bu malzemelerin
korozyon performansı, ağırlıkça % 0.9 NaCl içeren izotonik çözeltide test edildi. Korozyon
performansını değerlendirmek için açık devre potansiyel ölçümü (OCP), potansiyodinamik
polarizasyonu, dönüşümlü voltametri (CV) ve elektrokimyasal empedans spektroskopisi (EIS)
gibi elektrokimyasal yöntemler kullanılmıştır. Öte yandan, AZ91 ve AM60 magnezyum
alaşımlarının aşınma performansı 1 N, 3 N ve 5 N yükleri altında kuru ve ağırlıkça % 0.9 NaCl
izotonik çözelti ortamında tribometre (pin-on-disk metodu) kullanılarak araştırılmıştır.
Yapılan çalışma sonucunda, kriyojenik işlem görmüş AZ91 ve AM60 numunelerinin
işlem görmemiş numuneye kıyasla üstün korozyon direncine sahip olduğunu göstermektedir.
OCP sonuçları, kriyojenik olarak muamele edilmiş AZ91 ve AM60 alaşımlarının 1 saat sonra
ısıl işlem görmemiş numunelere göre daha iyi performans gösterdiği saptanmıştır. Diğer
taraftan, kriyojenik olarak işle görmüş AZ91 ve AM60'ın pasivasyon bölgesinin geniş ve anodik
çukurlaşma potansiyelinin (Epit) işlem görmemiş numunelere göre anodik olduğu
gözlemlenmiştir. Ayrıca, kriyojenik ısıl işlem görmüş numuneler AZ91 ve AM60 alaşımlarının
düşük korozyon reaksiyonlarına sahip olduğu EIS yöntemiyle tespit edilmiştir. Aşınma testinde,
aşınma izlerinin artan yük ile beraber genişliğinin arttığını tüm numuneler için görülmüştür.
Bunun yanında, düşük (1 N) ve orta yükte (3 N) ısıl işlem görmüş numunelerin aşınmaya karşı
daha dirençli olduğu tespit edilmiştir. Kuru ortamda kriyojenik işlem görmüş numunelerin
aşınmaya karşı daha dirençli fakat ağırlıkça % 0.9 NaCl çözelti ortamında ısıl işlem görememiş
numunelere göre aşınmalarının zayıf olduğu belirlenmiştir
In this study, untreated and cryogenically treated at -196oC for 48 h AZ91 and AM60
magnesium alloy were employed. The corrosion performance of the AZ91 and AM60 samples
was tested in isotonic solution containing 0.9% NaCl. Electrochemical methods such as the
open-circuit potential measurement (OCP), potentiodynamic polarization, cyclic voltammetry
(CV), and electrochemical impedance spectroscopy (EIS) were used to evaluate the corrosion
performance. On the other hand, wear behavior performance of AZ91 and AM60 magnesium
alloy were investigated in a dry and in 0.9 wt. % NaCl medium. The wear performance is
investigated under loads of 1 N, 3 N, and 5 N using a tribometer (pin-on-disc method) and
profilometer for each sample in both medium. An optic microscope is used to examine the forms
of wear endured and to measure the width of the wear track to determine the depth of penetration
in comparison to the samples. The analysis of variance method is also performed to find the
relationship between parameters.
The results show that the cryogenically treated AZ91 and AM60 samples hold superior
corrosion resistance when compared to the former sample. The OCP results indicated that the
cryogenically treated AZ91 and AM60 outperformed untreated samples after 1 h. The
potentiodynamic studies presented that cryogenically treated AZ91 and AM60 had superior
anodic pitting potential (Epit) and that the passivation zone is higher than AZ91 and AM60
when untreated. The EIS confirmed lower corrosion kinetics for AZ91 and AM60 treated in the
former sample. Regarding to wear behavior, it was observed for all samples that the width of
the wear tracks increased with increasing load. In addition, heat treated samples at low (1 N)
and medium load (3 N) were found to be more resistant to abrasion. It has been determined that
the samples that are cryogenic treated are more resistant to abrasion in dry environment, but
they are weak in 0.9 wt. % NaCl solution medium in comparison with the samples that have not
been heat treated